[1] Radford D W. Cure shrinkage induced warpage in flat uni-axial composites. Journal of composites technology & research， 1993，15(4)：290-296.
[2] Yang S Y， Huang C K. Curvature predictions of flat advanced composite tools based on measured volume fraction gradient. Journal of advanced materials, 1997，28(2)：47-55.
[3] Patterson J M， Springer G S， Kollar L P. Experimental observations of the spring-in phenomenon. Proceedings of the 8th International Conference on Composite Materials, 1991：10-D-1-10-D-8.
[4] Stephen A， Schwinge E， Muller J， et al. On the springback effect of CFRP stringers： an experimental， analytical and numerical analysis. Proceedings of the 28th International SAMPE Technical Comference, Seattle：1996.
[5] Rennick T， Radford D W. Components of manufacturing distortion in carbon fiber/epoxy angle brackets. Proceedings of the 28th international SAMPE Technical Conference, Seattle, 1996：189-97.
[6] Fernlund G， Rahman N， Courdji R， et al. Experimental and numerical study of the effect of cure cycle， tool surface， geometry， and the lay-up on the dimensional stability of autoclave-processed composite parts. Composites Part A： Manufacturing, Seattle, 2002，13(3)：341-51.
[7] Kim C G， Kim T W， Kim I G， et al. Spring-in deformation of composite laminated bends. Proceedings of the 7th international conference on composite materials (ICCM7), Beijing, 1989：83-88.
[8] Wiersma H W， Peeters J B， Akkerman R. Pridiction of spring-forward in continuous-fibre/polymer L shaped parts. Composites Part A, 1998, 29A(11)：1333-1342.
[9] Radford D W， Rennick T. Separating sources of manufacturing distortion in laminated composites. Journal of Reinforced Plastics and Composites, 2000，19(8): 621-641.
[10] White S R， Hahn H T. Cure cycle optimization for the reduction of processing-induced residual stresses in composite materials. Journal of Composite Materials, 1993, 27(14)：1352-1378.
[11] Fernlund G， Poursartip A. The effect of tooling material， cure cycle， and tool surface finish on spring-in of autoclave processed curved composite parts. Proceedings of the 12th International Conference on Composite Materials ( ICCM12), 1999.
[12] Jognston A， Hubert P， Fernlund G， et al. Poursartip A. Process modeling of composite structures employing a virtual autoclave concept. Science and Engineering of Composite Materials,1996, 5(3-4)：235-252.
[13] Radford D W， Diefendorf R J. Shape instabilities in composites resulting from laminate anisotropy. Journal of Reinforced Plastics and Composites, 1993, 12: 58-75.
[14] Huang C K， Yang S Y. Short communication-warping in advanced composite tools with varying angles and radii. Composites Part A, 1997, 28A: 891-893.
[15] Gasick M F， Renieri G D. Analysis techniques for the prediction of springback in formed and bonded composite components. N95-28289 Mcdonnell Aircraft Company, 1995: 1539-1558.
[16] Jain L K， Mai Y W， Stresses and deformations induced during manufacturing.Part I. Journal of Composite Materials, 1997，31：672-695.
[17] Padovec Z， Růžička M， Chlup H, et al. Springforward phenomenon on angular sections of composite materials-analytical. Numerical and Experimental Approach. Bulletin of Applied Mechanics, 2011, 7(26): 31-36.
[18] 党嘉立. 复合材料角型材结构固化变形研究. 宇航材料工艺，1993，5：10-12.
[19] Dai D, Qiao X, Liu S G. Calculations of cure deformation of single-curved composite laminates. Aeronautical Manufacturing Technology, 1999，5: 46-58.
[20] 戴福洪，张博明，杜善义. 复合材料非对称正交薄层板的固化变形. 复合材料学报，2006，23(4)：164-168.
[21] 任立波，罗小东，崔德刚. 复合材料非对称正交层合薄壳固化变形研究. 航空学报，2006，17(7)：128-130.
[22] 戴福宏，张博明，杜善义. 非对称复合材料薄层板固化变形及其应用. 哈尔滨工业大学学报，2008，40(1)：58-60.
[23] 寇哲君，戴棣，曹正华. 复合材料结构固化变形预测. 材料工程，2007（增1）：225-228.
[24] 李君，姚学锋，刘应华，等. 复合材料T型整体化结构固化翘曲变形模拟. 复合材料学报，2009，26(1):156-161.
[25] 张继奎，郦正能，关志东，等. 热固性复合材料固化过程三维有限元模拟和变形预测. 复合材料学报，2009，26(1):174-178.
2013, 
