[1] 邵忠喜. 纤维铺放装置及其铺放关键技术研究[D]. 哈尔滨：哈尔滨工业大学，2010.
[2] van Barschot J. Airbus en boeing vliegen met ten cate[N]. NRC Handelsblad, Rotterdam, 2005-01-05(17).
[3] Lamontia M A, Gruber M B, Tierney J J, et al. Modeling the accudyne thermoplastic in situ ATP process // 30th International SAMPE Europe Conference. Paris: SAMPE, 2009.
[4] Ghasemi N M N. Three-dimensional thermal and residual stress analysis of in-situ thermoplastic composite filament winding[D]. Department of Mechanical Engineering, University of Delaware, Newark, Delaware, 1992.
[5] Ghasemi M N. Thermal analysis for thermoplastic composite tow/tape preheating and pultrusion. Journal of Thermoplastic Composite Materials, 1997, 10(6): 504-523.
[6] Colton J, Leach D. Processing parameters for filament winding thick-section PEEK/carbon fiber composites. Polymer Composites, 1992, 13(6): 427-434.
[7] Pitchumani R, Don R C, Gillespie J W, et al. Analysis of on-line consolidation during thermoplastic tow-placement process. Thermal Processing of Materials, 1994, 289: 223-239.
[8] Lee M. Heat transfer and consolidation modeling of composite fiber tow in fiber placement[D]. Department of Mechanical Engineering, Virginia Polytechnic Institute and State University, Virginia, Blacksburg, 2004.
[9] Grove S M. Thermal modeling of tape laying with continuous carbon fiber-reinforced thermoplastic. Composites, 1988, 19(2): 367-375.
[10] Ghasemi N M N, Cope R D, Güceri S I. Thermal analysis of in situ thermoplastic composite tape laying. Journal of Thermoplastic Composite Materials, 1991, 4(1): 20-45.
[11] Turnkor S, Turkmen N, Chassapis C, et al. Modeling of heat transfer in thermoplastic composite tape lay-up manufacturing. Heat Mass Transfer, 2001, 28(1): 49-58.
[12] 张晓明，刘亚雄. 纤维增强热塑性复合材及其应用. 北京：化学工业出版社，2007：245-247.
[13] Jandal M Z, Widmann G. 热分析应用手册系列丛书：热塑性聚合物. 上海:东华大学出版社，2008：1-20.
[14] 金日光, 华幼卿. 高分子物理. 北京:化学工业出版社, 2007：80-110.
[15] Tierney J J, Gillespie J W, Jr. Crystallization kinetics behavior of PEEK based composites exposed to high heating and cooling rates. Applied Science Manufacturing (Composites, Part A), 2004, 35(5): 547-558.
[16] Boutaous M, Brahmia N, Bourgin P. Parametric study of the crystallization kinetics of a semi-crystalline polymer during cooling. Comptes Rendus Mecanique, 2010, 338(2): 78-84.
[17] Tierney J J, Gillespie J W, JR. Modeling of situ strength development for the thermoplastic composite tow placement process. Journal of composite materials, 2006, 40(16): 1487-1506.
[18] Dara P H, Loos A C. Thermoplastic matrix composite processing model. Virginia Polytechnic Institute and State University, Virginia, Blacksburg, 1985.
[19] Lee W I, Springer G S. A model for the manufacturing process of thermoplastic matrix composites. Composite Materials, 1987, 21(11): 1017-1987.
[20] Mantell S C, Springer G S. Manufacturing process models for thermoplastic composites. Composite Materials, 1992, 26(16): 2348-2377.
[21] de Gennes P. Reptation of a polymer chain in the presence of fixed obstacles. Chemical Physics, 1971, 55(2): 572-579.
[22] Doi M, Edwards S F. Dynamics of concentrated polymer systems. Faraday Transactions, 1978, 74(1): 1789-1801.
[23] Bastien L J, Cillespie J W, Jr. A nonisothermal healing model for strength and toughness of fusion bonded joints of amorphous thermoplastics. Polymer Engineering and Science, 1991, 31(24):1720-1730.
[24] Yang F, Pitchumani R. Healing of thermoplastic polymers at the interface under nonisothermal conditions. Macromolecules, 2002, 35(8): 3213-3224.
[25] 张振甫，肖军，吴海桥，等. 复合材料锥壳0°铺层的自动铺放成型方法研究. 宇航材料工艺，2007(2): 55-57.
[26] 安鲁陵，周燚，周来水. 复合材料纤维铺放路径规划与丝数求解. 航空学报, 2007, 28(3): 745-750.
[27] 尹洪玉. 纤维铺放运动轨迹规划及仿真系统研究[D]. 哈尔滨: 哈尔滨工业大学，2007.
本文共有参考文献35篇，因篇幅有限，未能一一列出，如有需要，请向本刊编辑部索取。
2012, 
